Question about product or request a quote

An internal, solid rolling bar (Ø 12 mm V2A) rotates away during a sawing attempt – cutting through with a normal saw is not possible. The outer tube is available in Ø 33.7 or 42.4 mm (from 1500 mm length we recommend 42.4 mm); hardened balls in the hexagon sockets prevent removal.

Two use cases. As mechanical burglary protection in front of windows on the ground floor, in the basement or on sides of the house that are hard to see – more discreet than a window grille, because only one tube sits in front of the pane and it barely obstructs the view. And as fall protection in front of floor-to-ceiling windows and doors that open for ventilation.

For the second case, choose one of the three mounting kits with M10 anchors in the configurator: there the forces act perpendicular to the wall, and screws with wall plugs are not designed for that. The height a barrier at your window has to reach is governed by the building regulations of your federal state – if in doubt, just give us a quick call.

Yes – with the right fixing material. With burglary protection, someone pulls on the bar from outside; with fall protection, someone pushes against it from inside. That is a different load direction, and it determines the anchoring.

Instead of the Torx security screws you then need M10 anchors. Three sets are available in the configurator, depending on the wall construction: masonry (brick, aerated concrete), external thermal insulation systems up to 200 mm insulation thickness with a thermally separated anchor, and timber frame construction with a Rampa insert. These are the same sets we supply for our French balconies.

The height at which the barrier has to sit is set out in the building regulations of your federal state. Send us a photo of the window situation if you are unsure.

High-quality, rust-free 1.4301 (V2A) stainless steel, brushed. The wall-mounting elements are also made of stainless steel. Manufactured in Germany.

You state the fixing distance in millimeters – the clear dimension between the two reveal walls the bar is fixed to. Measure at the narrowest point; old plaster rarely runs straight.

We manufacture 5 mm shorter than ordered. The slip-over sleeves make up this clearance again – without it you would not get the bar into the opening. Lengths from 250 to 2000 mm are possible.

If you are unsure about taking the measurements, send us a photo of your window situation. We will tell you what to measure – free of charge.

That depends on the use case. For burglary protection the Torx security screws are enough: 7×50 mm in normal masonry, 7×105 mm if you have to reach through thick plaster or a soft layer into the load-bearing substrate.

If you use the bar as fall protection, the forces act perpendicular to the wall – then you need M10 anchors. Three sets are available: masonry (brick, aerated concrete), external thermal insulation systems up to 200 mm insulation thickness with a thermally separated anchor, and timber frame construction with a Rampa insert.

The Security Bar III is fixed into the wall with one screw per wall connection, so it has two fixing points. The sets are sized accordingly as 2-piece sets.

Für Produkte mit dem EU-Label GARAN auf der Produktseite geben wir eine Herstellergarantie auf das ganze Produkt, auch auf die Oberfläche. Wie lange sie läuft, steht im Label: 5 Jahre bei Französischen Balkonen und Fenstergittern sowie bei den Überdachungen Köln, Leipzig, Siegen, Passau, Regensburg, Paris und Bamberg, 10 Jahre bei Fahrradhäusern und Mülltonnenboxen. Die Garantie kostet Sie nichts und kommt zur gesetzlichen Gewährleistung von mindestens zwei Jahren hinzu. Sie gilt für das Produkt selbst, nicht für die Montage, auch nicht für den Aufbau eines Bausatzes. Produkte ohne GARAN-Label haben die gesetzliche Gewährleistung. Alle Einzelheiten stehen in unseren Garantiebedingungen.